The Fangkuai Group's unique full-operating boiler operation laboratory has an annual operating cost of more than 5 million yuan, which can simulate the operating conditions of various types of boilers under multi-operating environment conditions. The laboratory provides technical tests such as test and inspection, analysis and evaluation, data evaluation, energy saving and environmental protection, and special software from materials to complete equipment, hardware to software, and even complex large systems.

In theory, the boiler fuel consumption under ideal operating conditions = boiler output / fuel calorific value / boiler thermal efficiency.

1. Boiler output refers to boiler power. Steam boilers generally refer to evaporation (t/h), and hot water boilers are thermal power (MW). So far, ZG boiler has been able to produce nine systems and more than 200 products. The wns series horizontal oil and gas boilers produced by ZG boiler have a capacity range of 1-20tph.

2. Boiler thermal efficiency refers to the percentage of effective heat and heat input to the boiler at the same time. Like the wns series of fire tube oil and gas boilers produced by ZG boiler, the thermal efficiency is high, up to 98%.

Tail secondary combustion flue how to deal with the phenomenon of a sharp increase in rear of the boiler flue secondary combustion flue temperature location and later. 2, the furnace, the flue abrupt change in negative pressure, flue gas is not tight at the smoke, the Mars. 3, air preheater large current swing bearing housing temperature, severe Jam occurs. 4, air preheater fire alarm issue. 5, steam temperature, economizer outlet water temperature, the air temperature rises abnormally. 6, induced draft fan vanes automatically open a large, Fan current rise. 7, as the combustion side, both sides of the smoke temperature difference increases. Reason 1, through the coarse fine grinding coal, coal poor uniformity, improper adjustment of combustion, combustion of fuel is insufficient, serious mechanical incomplete combustion, and high levels of combustible ash accumulated in the back pass. 2, an oil burner or an oil poor atomization, so that unburned droplets deposited in the flue. 3, prolonged low load operation of boiler, the furnace temperature is too low or too small amount of excess air resulting in incomplete combustion of coal or oil accumulated in the tail. 4, after the shutdown of the fuel leakage into the furnace and accumulates or after shutdown and to insufficient MFT furnace purge unburnt coal or oil accumulation at the end of the tail. 5, soot blower failure, long-term put into operation is not normal. 1 process, when a slight secondary combustion, exhaust gas temperature does not rise within 20 ℃ normal smoking temperature should be checked immediately paragraphs, the combustion site and judge whether the secondary steam soot blowing. (When the exhaust gas temperature rises to 250 ℃) 2, the operation of the back pass and then generating boiler combustion boiler operation should be stopped immediately, immediately stop sending, ID fan and turn off all the smoke and steam soot blowing air damper fire. 3, if the economizer afterburning, until the storage tank level control valve blocking off without pressure, flow rate of feed pump motor start 150t / h Sheung be cooled. 4, air preheater heating surface of the secondary combustion air preheater normal operation, normal operation of the air pre-heater holder; air preheater Jam occurs, the main drive motor and the auxiliary drive motor trip, contact maintenance manual plate moving continuous air preheater rotor. Soot blowing steam into air preheater for extinguishing, into the air preheater for fire extinguishing can not be extinguished. 5, the economizer outlet water temperature close to the inlet temperature (at the economizer secondary combustion), the air preheater inlet gas temperature, exhaust gas temperature, the hot air temperature is lowered to less 80 ℃, each one hole, and the hole is no longer Mars smoke and soot blowing steam stops coming out after water or fire. Open hole inspection manhole and inspection to confirm the secondary combustion goes out, after the flue vent door open to drain water inside the smoke flue opening for ventilation air damper. 6, to be re-combustion is resolved, the flue temperature does not rise and fall when stabilized, before slow regulation of the air, smoke baffle, the necessary air cooling and purging.

Working principle and structural characteristics of 6000 kg industrial fired steam boiler

Steam boiler has brought great convenience to industry. Steam boiler has driven the development of the times. The following is a brief introduction to the structural characteristics and working principle of steam boiler. Steam boiler is a machine that mainly produces steam, and many people use it, but many of them do not know much about its structure and working principle. It makes use of coal, oil, natural gas and other water-tube steam boilers with limited capacity and pressure. There is a large desire to space, and easy to arrange, steam boiler in a variety of forms. Water is heated in the drum into steam, and the heat emitted by fire in the furnace is the principle of a steam boiler. Work of steam boiler Principle:

1, the heat generated by pulverized coal combustion in the furnace is first absorbed by the water wall through radiative heat transfer, and the water boiling of the water wall is vaporized, producing a large amount of steam into the steam drum for steam separation (except for direct flow furnaces). The separated saturated steam enters the superheater and continues to absorb the flue gas heat at the top of the furnace and the horizontal flue and the tail flue through radiation and convection, and enables the superheated steam to reach the required working temperature. The steam boiler for power generation is usually equipped with a reheater, which is used to heat the steam after the high-pressure cylinder does work, and the reheat steam comes out of the reheater to go back to the middle, and the low-pressure cylinder continues to do the work to generate electricity.

2. When the pulverized coal stove is working, The position of the center of the flame will affect the amount of evaporation, generally speaking, if the center of the flame is low, the amount of evaporation will be large, and the position of the center of the flame will also affect the temperature of the superheated steam or reheated steam, as well as the high value of the flame center and the small amount of evaporation. When the flame center is low, the superheated steam, especially the reheated steam temperature, will be low and vice versa.

3, the arrangement of burners, as far as coal powder furnace is concerned, there are many kinds of combustion modes, such as front and rear wall, tangential combustion, double tangential combustion, and so on, each of which has its own characteristics. The influence on steam can not be directly determined because the same furnace can not apply the above-mentioned arrangement methods at the same time.